VOM160 www.vishay.com vishay semiconductors rev. 1.6, 22-may-12 1 document number: 81349 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 optocoupler, phototriac output, non-zero crossing, 0.5 kv/s dv/dt, 600 v description the VOM160 series phototriac consist a algaas infrared emitting diode (ired) optically coupled to a photosensitive non-zero crossing triac packaged in a sop-4 package. it has a ired trigger current of 5 ma, 7 ma, and 10 ma. the VOM160 series phototriac isolate low-voltage logic from 120 v ac , 240 v ac , and 380 v ac lines to control resistive, inductive, or capacitive loads including motors, solenoids, high current thyristors or triac and relays. features ? high static dv/dt > 0.5 kv/s ? input sensitivity i ft = 5 ma, 7 ma, and 10 ma ? on-state rms current i t(rms) = 70 ma ? 600 v peak off-state blocking voltage ? isolation test voltage 3750 v rms ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 applications ? consumer appliances ? triac drives ?solid-state relays ? motor controls ? office equipment agency approvals ? ul1577, file no. e52744, double protection (pending) ? cul-file no. e52744, equivalent to csa bulletin 5a (pending) ? vde 0884-5, din en 60747-5-5 ? cqc (pending) notes ? for additional information on the available options refer to option information. ? the product is available only on tape and reel. mt1 mt2 a c 1 2 4 3 i179066 ordering information vom1 6 0xt part number agency certified/package trigger current i ft ul, cul, cqc 5 ma 7 ma 10 ma sop-4 VOM160nt VOM160pt VOM160rt vde, ul, cul, cqc 5 ma 7 ma 10 ma sop-4 VOM160n-x001t VOM160p-x001t VOM160r-x001t s op-4 7.21 mm
VOM160 www.vishay.com vishay semiconductors rev. 1.6, 22-may-12 2 document number: 81349 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 notes ? stresses in excess of the abso lute maximum ratings can cause pe rmanent damage to the device. functional operation of the devic e is not implied at these or any other conditions in excess of those give n in the operational sections of this document. exposure to abs olute maximum ratings for extended periods of the time can adversely affect reliability. (1) wave soldering three cycles are allowed. also refer to assembly instructions for surface mounted devices ( www.vishay.com/doc?80054 ). fig. 1 - recommended operating condition absolute maximum ratings (t amb = 25 c, unless otherwise specified) parameter test condition part symbol value unit input reverse voltage v r 6v forward current i f 60 ma peak surge current 100 s, 200 pps i fsm 0.5 a power dissipation p diss 100 mw output peak off-state voltage v drm 600 v rms on-state current i t(rms) 70 ma peak non-repetitive surge current pw = 100 ms, 120 pps i tsm 1a power dissipation p diss 200 mw coupler isolation test voltage t = 1 min v iso 3750 v rms power dissipation p tot 300 mw storage temperature range t stg - 55 to + 150 c ambient temperature range t amb - 40 to + 100 c soldering temperature (1) t sld 260 c 0 20 40 60 80 100 - 40 - 20 0 20 40 60 80 120 t amb - temperature (c) i l - load current (ma) 100
VOM160 www.vishay.com vishay semiconductors rev. 1.6, 22-may-12 3 document number: 81349 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note ? minimum and maximum values were tested requirements. typical values are characteristics of the device and are the result of en gineering evaluations. typical values are for information only and are not part of the testing requirements. electrical characteristics (t amb = 25 c, unless otherwise specified) parameter test condition part symbol min. typ. max. unit input forward voltage i f = 10 ma v f 1.2 1.5 v reverse current v r = 6 v i r 10 a input capacitance v f = 0 v, f = 1 mhz c i 25 pf output off-state current v d = v drm i drm 100 na on-state voltage i t = 100 ma v tm 2.8 v critical rate of rise off-state voltage v d = 0.67 v drm , t j = 25 c dv/dt cr 500 v/s critical rate of ri se of voltage at current commutation dv/dt crq 0.13 v/s coupler led trigger current, current required to latch output v d = 3 v VOM160n i ft 5ma VOM160p i ft 7ma VOM160r i ft 10 ma capacitance (input - output) f = 1 mhz, v io = 0 v c io 0.8 pf peak off-state voltage i c = 100 a v drm 600 v holding current i hold 0.3 ma safety and insulation ratings parameter symbol min. typ. max. unit climatic classification (accordi ng to iec 68 part 1) 40/100/21 pollution degree (din vde 0109) 2 comparative tracking index cti 175 399 peak transient overvoltage v iotm 6000 v peak peak insulation voltage v iorm 707 v peak isolation resistance at t amb = 100 c, v dc = 500 v r io 10 11 isolation resistance at t amb = 25 c, v dc = 500 v r io 10 12 safety rating - power rating p so 400 mw safety rating - input current i si 150 ma safety rating - temperature t si 165 c creepage distance 5mm clearance distance 5mm insulation thickness 0.4 mm
VOM160 www.vishay.com vishay semiconductors rev. 1.6, 22-may-12 4 document number: 81349 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 typical characteristics (t amb = 25 c, unless otherwise specified) fig. 2 - forward current vs. forward voltage fig. 3 - reverse voltage vs. ambient temperature fig. 4 - on-state curr ent vs. on-state voltage fig. 5 - off-state leakage current vs. ambient temperature fig. 6 - normalized trigger current vs. ambient temperature fig. 7 - trigger current vs. turn-on time 0.8 1.4 1.6 1 10 100 v f - forward voltage (v) i ft - forward current (ma) - 40 c 0 c 25 c 50 c 85 c 100 c 1.2 1.0 21983 0 20 40 60 80 100 - 40 - 20 20 04080 60 100 v r - reverse voltage (v) t amb - ambient temperature (c) 21982 - 100 - 75 - 50 - 25 0 25 50 75 100 i tm - on-state current (ma) v tm - on-state voltage (v) - 2.5 - 2 - 1.5 - 1 - 0.5 0 0.5 1 1.5 2 2.5 21993 i drm - off-state leakage current (na) t amb - ambient temperature 0.1 1 10 100 1000 10 000 100 000 - 40 - 20 20 04080 60 100 21985 0.5 0.7 0.9 1.1 1.3 1.5 i ft - normalized trigger current (ma) t amb - ambient temperature (c) v d = 3 v - 40 - 20 20 04080 60 100 21987 1 10 100 10 50 turn-on time (s) i ft - trigger current (ma) v l = 7 v 20 30 40
VOM160 www.vishay.com vishay semiconductors rev. 1.6, 22-may-12 5 document number: 81349 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 8 - normalized holding current vs. ambient temperature fig. 9 - trigger current vs. delay time fig. 10 - trigger current vs. trigger pulse width fig. 11 - trigger current vs. load voltage 21986 0 0.5 1.0 1.5 2.0 2.5 - 40 - 20 20 04080 60 100 i h - normalized holding current (a) t amb - ambient temperature (c) 21988 1 10 100 10 20 40 50 t gd - delay time (s) i ft - trigger current (ma) 30 21989 2 3 4 5 6 7 8 20 40 60 80 100 i ft - trigger current (ma) p w - trigger pulse width (s) v l = 7 v 21990 3 4 5 6 7 8 0 100 200 300 400 500 600 i ft - trigger current (ma) v load - load voltage (v)
VOM160 www.vishay.com vishay semiconductors rev. 1.6, 22-may-12 6 document number: 81349 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 package dimensions in millimeters package marking (example) tape and reel packaging dimensions in millimeters fig. 12 - tape and reel shipping medium (eia-481, revision a, an d iec 60286), 2000 units per reel fig. 13 - tape dimensions r 0.25 0.91 0.36 5.08 1.14 7.37 2.54 m160n v yww u68 pin 1 i.d. ink mark esd sticker tape slot in core 330 (13") regular, special or bar code label 17999 22646 7.33 0.1 1 2 3 4 8 2.66 0.1 2.00 0.05 4.00 0.1 1.50 0.1 1.75 0.1 5.50 0.05 1.50 0.25 4.72 0.1 8.00 0.1 12.00 + 0.3 - 0.1
legal disclaimer notice www.vishay.com vishay revision: 12-mar-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products no t expressly indicated for use in such applications do so at their own risk and agr ee to fully indemnify and hold vishay and it s distributors harmless from and against an y and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale , including attorneys fees, even if such claim alleges that vis hay or its distributor was negligent regarding th e design or manufacture of the part. please contact authorized vishay personnel t o obtain written terms and conditions regardin g products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu.
|
